Choosing Between Console Tables from a Catalogue and a Fully Bespoke Design for Worldwide Delivery
Catalogue or bespoke is not a binary choice. This guide explains the middle path of modifying an existing model, and how each route affects time, cost and risk on international hotel projects.
A bespoke console table gives you full control over proportions, materials and detailing, while a catalogue model gives you speed and a proven construction. Most hotel buyers assume they must pick one or the other. In practice there is a third route: taking a catalogue design and modifying it to suit your project. This article compares the three routes and explains what each means for time, cost and approvals when the pieces are made to order and shipped worldwide.
The three routes at a glance
Before comparing details, it helps to define the options clearly. Factories use different words, so agree on terms early in the conversation.
- Catalogue model as shown: an existing design produced in the dimensions and finishes already offered.
- Modified catalogue model: an existing design with agreed changes, such as new dimensions, a different wood species or a revised top.
- Fully bespoke design: a new piece developed from your sketch, reference photo or designer drawings.
All three can be treated as a made to order console table. The difference lies in how much engineering and sampling the factory must do before mass production starts.
Comparing catalogue vs custom furniture
The table below summarises the general differences. Actual figures depend on the project, so treat it as a planning aid rather than a quotation.
| Factor | Catalogue as shown | Modified catalogue | Fully bespoke |
|---|---|---|---|
| Design development | None or minimal | Limited revision of existing drawings | New drawings and construction logic |
| Sampling | Finish sample, often a piece | Prototype of the changed areas or full piece | Full prototype, often more than one round |
| Lead time | Shortest | Moderate | Longest |
| Unit cost | Lowest of the three, usually | Slightly higher, depending on changes | Highest, especially on small runs |
| Design freedom | Low | Medium | Full |
| Technical risk | Low | Low to medium | Medium to high |
When a catalogue model is enough
A catalogue piece suits you when the design intent is flexible and the schedule is tight. It also works well for secondary areas such as corridors, back-of-house lounges or serviced rooms where the console supports the space rather than defining it.
Because the construction has already been resolved, you know how the leg-to-top connection, edge detailing and finish behave. That reduces the number of questions during approval. If your designer can accept the standard sizes, it is usually the most efficient route.
When a fully bespoke design makes sense
A bespoke console table is justified when the piece is part of the hotel's identity: a lobby feature, a signature suite or a brand-defined detail. It is also the right answer when the architecture dictates unusual dimensions, curved walls, or specific integration with lighting, stone or metal.
The trade-off is development effort. The factory must convert your idea into shop drawings, choose joinery methods, build a prototype and often revise it. Each of these steps takes time, and you should include them in the project programme rather than treating them as a surprise.
What you should provide
- A clear brief with overall dimensions and tolerances.
- Reference photos, sketches or CAD files.
- Target quantity, since volume affects tooling and setup choices.
- Finish references, ideally a physical sample or a code.
- Destination country, so fire and material requirements are known.
The middle path: modify an existing design
If you want to modify an existing design, you keep the factory's proven structure and change only what the project needs. This is often the best balance for hotel buyers who want a distinctive result without a full development cycle.
Typical modifications include:
- Dimensions: adjusting length, depth or height to fit an entrance niche or corridor.
- Materials: switching from oak to walnut veneer, or adding a stone or glass top.
- Finish: matching a colour code or a different gloss level.
- Storage: adding a drawer, a shelf or a cable cut-out.
- Details: changing leg style, edge profile or hardware.
How modifications affect time
A small change, such as a new finish, usually needs only a finish sample. A dimensional change may require updated drawings and a prototype. A structural change, such as adding drawers or replacing the base, can approach the effort of a new design.
As a rule, the more the change touches construction rather than appearance, the more time you should allow. We do not quote fixed timings in general terms because they depend on the model, the workload at the factory and how quickly approvals are returned.
How modifications affect cost
Cost moves with three things: additional engineering time, extra sampling and any change in material or labour content. Increasing a piece by a modest amount in length may change cost very little, while introducing a new material or a complex detail can change it noticeably.
Quantity matters too. Setup work is spread across all pieces, so a modification on a large batch has a smaller effect per unit than the same change on a handful of pieces.
A practical decision guide
Use these questions to place your project on the right route.
- Does the piece need to be unique to your brand? If yes, lean towards bespoke.
- Can the design work if dimensions and finish change but the form stays? If yes, modify a catalogue model.
- Is the opening date fixed and close? If yes, limit changes and use a catalogue model or a light modification.
- Is the quantity small? If yes, consider that bespoke setup cost will weigh heavily per piece.
- Will the same design repeat across several hotels? If yes, investing in a bespoke design may pay back over time.
Approvals and sampling for overseas projects
When the factory and the project are in different countries, approvals take longer simply because of distance and communication. Choose the route with that in mind, and decide who signs off drawings and samples on your side.
For modified or bespoke pieces, we recommend approving in this order: drawings, finish sample, then a prototype or first piece. Skipping the prototype may save time at the start but increases the risk of corrections after production has begun.
Logistics and delivery worldwide
Production is only part of the schedule. Packing, export documents and shipping terms such as EXW, FOB, CIF or DAP should be agreed before the order is released. Bespoke and modified pieces may have unusual sizes or fragile parts such as stone tops, so packing methods need to be confirmed together with the design.
Because we produce to project drawings in our own factory in Istanbul, we can coordinate design, production and export packing in one process. Delivery planning for Europe, the Middle East, Central Asia and Africa will differ, so the route and timing should be discussed per project.
Common mistakes to avoid
- Treating a modification as free. Even small changes need drawing updates and approval.
- Changing the design after sample approval, which restarts part of the process.
- Leaving finish decisions until late, when they can delay the whole batch.
- Ignoring fire or material rules in the destination country.
Conclusion
The choice is not simply catalogue or bespoke. A catalogue model gives speed, a bespoke design gives uniqueness, and a modified catalogue piece often delivers a distinctive result with less time and cost than a fully new development. Decide how much of the design truly needs to be unique, and let that guide the route.
If you are planning a hotel or hospitality project, send us your drawings, a reference photo or a short brief. We will review which route fits best and come back with suggestions on materials, sampling and delivery for your destination.
Sıkça Sorulan Sorular
What is the difference between a catalogue and a bespoke console table?
A catalogue console table is an existing design produced in offered sizes and finishes. A bespoke console table is developed from your brief, with new drawings and a prototype. Bespoke gives more design freedom but usually needs more time, sampling and budget.
Can I modify an existing console table design?
Yes. Many buyers adjust dimensions, wood species, finish, top material or storage on an existing model. Appearance changes are usually quick to review, while structural changes may need new drawings and a prototype before production.
Does a modified design take longer than a catalogue piece?
Generally yes, because drawings must be updated and a sample may be needed. How much longer depends on the extent of the changes, the factory workload and how fast you return approvals, so timing is confirmed per project.
Is a made to order console table more expensive?
Made to order does not automatically mean expensive. Cost depends on materials, complexity, sampling and quantity. Catalogue models are usually the most economical route, while bespoke designs carry extra development cost, especially on small runs.
Can you deliver custom console tables worldwide?
Yes, we produce to order in Istanbul and export to different regions. Shipping terms such as FOB, CIF or DAP, packing methods and delivery routes are agreed per project so the pieces arrive protected and in the right sequence.
Every hotel project is different. Send us your drawings or room schedule for a tailored proposal on materials, lead time and shipping.




